View ACM2520_7035296.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

july 2013 common mode filters for high-speed differential signal line, general signal line acm series acm2012 [0805 inch]* ACM2520 [1008 inch] * dimensions code jis[eia] emc components
(2/11) 001-01 / 20130723 / e9712_acm.fm emc components reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 6 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 75 % rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/11) 001-01 / 20130723 / e9712_acm.fm ? all specifications are subject to change without notice. emc components common mode filters for high-speed differential signal line, general signal line features downsized wound type chip common mode filter that maintains requi red common mode filter characteristics. impedance for common mode noise can clear 1000 [100mhz], and has excellent emc suppression. differential mode impedance is suppressed, so there is virt ually no affect on high speed signals. there is a two-line type and a three-line type, so they can be used for various circuits and noise. application common mode noise countermeasure for high-speed differential signals where influence to the signal is a concern. usb line for pcs and peripheral devices. ieee1394 lines and ethernet lines for pcs, stbs, etc. lcd panel lvds and panel link lines. part number construction operating temperature range, package quantity, product weight the storage temperature range is for after the circuit board is mounted. overview of the acm series acm 2012 - 900 - 2p - t - 002 series name lwh dimensions impedance number of lines packaging style internal code (mm) ( ) at 100mhz 2012 2.01.21.3 900 90 2p 2 lines t ?180mm reel 2520 2.52.01.2 201 200 3p 3 lines tl ?330mm reel 102 1000 type temperature range reel diameter package quantity individual weight operating temperature storage temperature c c mm pieces/reel mg acm2012 C40 to +85 C40 to +85 ?180 2,000 10 ?330 10,000 ACM2520 C40 to +85 C40 to +85 ?180 2,000 25 ?330 10,000 product compatible with rohs directive compatible with lead-free solders rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://www.t dk.co.jp/rohs/
(4/11) 001-01 / 20130723 / e9712_acm.fm ? all specifications are subject to change without notice. emc components overview of the acm series recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 10 to 30s 245c 5s natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature
(5/11) 001-01 / 20130723 / e9712_acm.fm ? all specifications are subject to change without notice. emc components acm series acm2012 type shape & dimensions recommended land pattern circuit diagram 2.0 0.2 1. 2 0.2 1.3max. 0.5 0.3 0.05 0.3 1.2 0.4 0.4 dimensions in mm 1.1 0.75 0.75 0.40.4 0.4 dimensions in mm 1 2 4 3 ? no polarity
(6/11) 001-01 / 20130723 / e9712_acm.fm ? all specifications are subject to change without notice. emc components acm series y acm2012 type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. impedance vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. impedance ( ) [100mhz dc resistance ( )max.[per line] rated voltage (v)max. rated current (a)max. part no. min. typ. 65 90 0.19 50 0.4 acm2012-900-2p-t002 90 120 0.22 50 0.37 acm2012-121-2p-t002 150 200 0.25 50 0.35 acm2012-201-2p-t002 270 360 0.5 50 0.22 acm2012-361-2p-t002 measurement item product no. manufacturer common mode impedance 4991a agilent technologies dc resistance 4338a agilent technologies insulation resistance 4339a agilent technologies product no. manufacturer 4991a agilent technologies 1 10 100 1000 10000 1000 100 1 10 frequency ( mhz ) impedance ( ) 201 common mode 900 common mode 121 common mode 361 common mode 121 differential mode 201 differential mode 900 differential mode 361 differential mode
(7/11) 001-01 / 20130723 / e9712_acm.fm ? all specifications are subject to change without notice. emc components acm series ACM2520-2p type shape & dimensions recommended land pattern circuit diagram 2.5 0.2 2.0 0.2 1.2 0.1 0.85 1.30 1.6 0.45 0.45 dimensions in mm 1.5 0.8 0.8 0.40 1.3 dimensions in mm 1 2 4 3 ? no polarity
(8/11) 001-01 / 20130723 / e9712_acm.fm ? all specifications are subject to change without notice. emc components acm series y ACM2520-2p type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. impedance vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. impedance ( ) [100mhz dc resistance ( )max.[per line] rated voltage (v)max. rated current (a)max. part no. min. typ. 225 300 0.35 20 0.4 ACM2520-301-2p-t002 330 450 0.4 20 0.35 ACM2520-451-2p-t002 450 600 0.45 20 0.3 ACM2520-601-2p-t002 750 1000 0.9 20 0.2 ACM2520-102-2p-t002 measurement item product no. manufacturer common mode impedance 4991a agilent technologies dc resistance 4338a agilent technologies insulation resistance 4339a agilent technologies product no. manufacturer 4991a agilent technologies 1 10 100 1000 10000 1000 100 1 10 frequency ( mhz ) impedance ( ) 601 common mode 301 common mode 451 common mode 102 common mode 451 differential mode 601 differential mode 301 differential mode 102 differential mode
(9/11) 001-01 / 20130723 / e9712_acm.fm ? all specifications are subject to change without notice. emc components acm series ACM2520-3p type shape & dimensions recommended land pattern circuit diagram 2.5 0.2 1.2 0.1 1.3=p0.652 0.85 1.6 0.45 0.45 1 2 3 6 5 4 2.0 0.2 dimensions in mm 1.5 0.8 0.8 0.35 1.3=p0.652 dimensions in mm 1 2 6 5 3 4 ? no polarity
(10/11) 001-01 / 20130723 / e9712_acm.fm ? all specifications are subject to change without notice. emc components acm series y ACM2520-3p type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. impedance vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. impedance ( ) [100mhz dc resistance ( )max.[per line] rated voltage (v)max. rated current (a)max. part no. min. typ. 600 800 1.6 20 0.15 ACM2520-801-3p-t002 measurement item product no. manufacturer common mode impedance 4991a agilent technologies dc resistance 4338a agilent technologies insulation resistance 4339a agilent technologies product no. manufacturer 4991a agilent technologies 1 10 100 1000 10000 1000 100 1 10 frequency ( mhz ) impedance ( ) 801 common mode 801 differential mode
(11/11) 001-01 / 20130723 / e9712_acm.fm ? all specifications are subject to change without notice. emc components acm series packaging style reel dimensions tape dimensions ty p e a w1 w2 n e acm2012 ?3302 9.50.5 13.51 1001 2 typ. ?1803 9+1/C0 131 60+1/C0 2 typ. ACM2520 ?3302 9.50.5 13.51 1001 2 typ. ?1803 9+1/C0 131 60+1C0 2 typ. dimensions in mm ty p e a b ?d0 e f p0 p1 p2 w k t acm2012 1.40.1 2.250.1 1.5+0.1/0 1.750.1 3.50.1 4.00.1 4.00.1 2.00.1 8.00.2 1.40.1 0.250.05 ACM2520 2.40.1 2.90.1 1.5+0.1/0 1.750.1 3.50.1 4.00.1 4.00.1 2.00.1 8.00.2 1.450.1 0.250.05 ?13.0 0.2 ?21.0 0.8 n e 2.0 0.5 a dimensions in mm 1.0 w2 w1 w f e p0 p1 p2 ?d0 b a t k 160min. taping 440min. drawing direction 500 to 560min. dimensions in mm

▲Up To Search▲

Price & Availability of ACM2520

	To Download ACM2520 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .